Voltage Divider+ Pre-Amplifier

This plug on module comes with the preamplifier and voltage divider. The module is used with the Scintillation detector. It can easily be mounted on the scintillation detector by simply inserting the 14 pins of the scintillation detector into the device base. The preamplifier used with the voltage divider is used to reduce the signal distortion of detected gamma rays.

Injection System

Pressurize Dispenser (PD) System works on the principle of Pneumatic pressure. PD (Pressurize Dispenser System) is a system in which the mixture of powder and gas is injected with high pressure.
The injection system has 2 Inlets (Air pressure inlet, Material inlet) and 2 Outlets (Vent Outlet and Product outlet). The Injection System consists of the pressure regulator, hose pipe, pressure gauge, flask, pivoted screw, cone/mixing chamber, and 4 ball valves viz.
1) Pressure inlet Valve
2) Material inlet Valve
3) Air Vent Valve
4) Product outlet.

Sediment Transport Studies/Under Water Radiation Detector

The system is used to measure sediment density transport in rivers, lakes, dams, etc. This device also measures the gamma radiations present in the water (in rivers, dams, lakes, etc.). The system has the arrangement to measure the equipment depth. All these parameters can be observed and analyzed on the software that is specially designed for the device.

Flow Rig

The flow rig / RTD simulator will be used to perform various permutations and combinations of flow rate, speed of the agitator, and type of the vessel to understand flow dynamics in scaled-down models of CSTR and column-type reactors.
In a centrally stirred tank reactor, steady-state flow conditions will be achieved using valves on the pipeline connected to the reactor with an agitator through a flow rate meter.

Automatic Column Scanning System

The scanner system is used for scanning large industrial boilers, petrochemical refineries, cement plants, chemical furnaces, mining plants, and chemical reactors. The system is also used to find out the fault/defect in the pipeline, the density of the liquid etc. for proper operation. The parameters of the system can be continuously monitored and controlled by the application software.

PWR Relay Crad

Features:

Relay Module for Industrial Suitability & Genet application.
LED indication to denote relay actuation.
Relay Coil Protection by means of a Freewheeling diode.
Reverse polarity protection.
Mounting Options available: DIN Rail mounting.

8W 2C REL V1.0

Features:

Relay Module for Industrial Suitability.
Easy to replace Pluggable Relays.
LED indication to denote relay actuation.
Relay Coil Protection by means of a Freewheeling diode.
Reverse polarity protection.
Mounting Options available: DIN Rail mounting.

4W ST SP Relay Card

Features:

Relay Module for Industrial Suitability & Genset application.
LED indication to denote relay actuation.
Relay Coil Protection by means of a Freewheeling diode.
Reverse polarity protection.
Mounting Options available: DIN Rail mounting.

4W Relay Card

Features:

Relay Module for Industrial Suitability.
LED indication to denote relay actuation.
Relay Coil Protection by means of a Freewheeling diode.
Reverse polarity protection.
Mounting Options available: DIN Rail mounting.

ST SP Relay Card

Features:

Relay Module designed for Industrial Suitability and Genset applications.
LED indication to clearly denote relay actuation.
Relay Coil Protection ensured by a Freewheeling diode.
Reverse polarity protection to enhance safety.
Mounting Options available: DIN Rail mounting.

2W 2C Relay Card

Features:

Relay Module for Industrial Suitability.
Easy to replace Pluggable Relays.
LED indication to denote relay actuation.
Relay Coil Protection by means of a Freewheeling diode.
Reverse polarity protection.
Mounting Options available: DIN Rail mounting.

4W 2C Relay Crad

Features:

Relay Module for Industrial Suitability.
Easy to replace Pluggable Relays.
LED indication to denote relay actuation.
Relay Coil Protection by means of a Freewheeling diode.
Reverse polarity protection.
Mounting Options available: DIN Rail mounting.

Magnetic Pickup Sensor

A magnetic pickup sensor is an electronic device that is used in various applications, such as automotive systems, industrial machinery, and Engine Control Unit (ECU). It is used to monitor the speed or position of rotating equipment to ensure the accurate control and synchronization of various processes of industrial machineries. In automotive applications, it is often used to measure the rotational speed or position of a rotating component, such as the crankshaft or camshaft in an engine.

Electrical Winch

A winch is an electromechanical device that is used to handle the tension of a wire cable. It consists of a spool on which the wire cable is wounded and a hand crank.

Pump Controller

This is GSM based smart pump Controller unit innovated to apply to control remote submersible pumps or motors used in farms, and plants.
The user can simply ON or OFF his pump or Motor by just sending Simple commands, and also get a confirmed SMS reply within a second. Users are also able to know the power status, and can set events or time required to operate the pump or motor.

Engine Controller

The ENGCON is an easy to use and designed to provide flexible control with built in monitoring and protection.
The unit incorporates both manual and auto start initiated start and stop sequencing, monitors engine and alternator operating parameters and provides both engine and alternator protection, in a single integrated package.
The Engine operating parameters are shown by scrolling screens on a backlit 128×64 GLCD. Alarms and warning messages are also shown on the LCD, supplemented by a corresponding LED and Hooter output.
The unit provides comprehensive monitoring of the engine operating parameters and provides automatic shutdown of the engine in the event of damaging conditions. In addition to the usual engine safety protections the unit monitors fuel level, engine temperature and engine loading to provide even more comprehensive protection.

Genset Controller

The GENCON is an integrated Engine and Generator controller for Gensets. The unit incorporates both manual and auto start-initiated start and stop sequencing, monitors engine and alternator operating parameters and provides both engine and alternator protection, in a single integrated package. The Genet operating parameters are shown by scrolling screens on a backlit 128×64 GLCD. Alarms and warning messages are also shown on the GLCD, supplemented by a corresponding LED and Hooter output.

12- Channel Counter

The 12-channel DAS consists of 12-detectors SCA (single channel analyser) with PC control of all necessary operating parameters. The 12 detectors are connected to the counter. Each detector has its own high voltage, window settings, and threshold points.
The density of any material/ object can be also checked without physical contact with the material/ object.

6 - Channel Counter

The six-channel DAS consists of 6-detectors SCA (single channel analyser) with PC control of all necessary operating parameters. The 6 detectors are connected to the counter. Each detector has its own high voltage, window settings, and threshold points.

Single Channel Analyser

The Single Channel DAS consists of SCA (single channel analyser) with PC control of all necessary operating parameters. The detector is connected to the counter. The detector has its own high voltage, window settings, and threshold points.

IN-PAD-LoRa

The Single channel LoRa-based DAS contains SiPM detectors. This radio tracing application is used for collecting data from remote locations. The detector of the system is placed at the remote location and the user can monitor the data at the receiver side using application.

IN-PAD-IoT (LDS)

The GSM-Based DAS uses an SiPM detector. The SiPM detector works on current-to-voltage converter topology. The data can be monitored remotely through the application software.

Voltage Divider

The 14-pin voltage divider is used with the scintillation detector. It can easily be mounted on the scintillation detector by simply inserting the 14 pins of the scintillation detector into the voltage divider base.

Smart SiPM

The Smart SiPM is a Smart Single Channel Analyzer. It transmits data through both mediums i.e. Wireless and Wired. In wireless mode, the data is transferred to the laptop through Wi-Fi and is observed on dedicated application software. The other way to collect or store or observe or monitor the data is through wired mode. The data can be transferred to any external device using an RJ45 connector and cable.

Pipe Scanning system

Pipe Scanning System: Yelsons offers a Pipe scanning system for different industrial, petrochemical refineries, cement plants, mining plants etc. to measure directly and continuously the concentration or density of a flowing material or a mixture inside pipe. And to evaluate the deposits by their measurements at various angles and, to measure sealing in pipes.

Sledge

Sledge is basically a holding device used for holding enclosure. Sledge is a submersible assembly that is made up of stainless steel 304 to keep it away from corrosion. The enclosure is held rigidly in the sledge. It has four pillars stud in which both the ends are having threading for bolts which can be adjusted to hold the enclosure rigidly. Sledge had a clamp which is used for holding the wire in this way assembly is ready to dive into the water.

IP-68 Enclosures

Enclosure is an air-tight container used to protect the detector from water and moisture damage in underwater condition where the surface tension is high. It is made up of polyethylene terephthalate (PET) material which makes it possible to sustain underwater for a certain limited extent (up to 100 meter). The sensor is inserted in this enclosure which makes it possible to dive underwater. The enclosure has a connector on the upper side to which the sensor is connected from inside. It also has two O-rings which makes it airtight. A C-Clamp is required to Cap tighten the lid. This enclosure is assembled in the sledge in such a way that the two groves of the enclosure get match to the two holes of the top plate of the sledge. The enclosure is rigidly fixed in the sledge assembly.

Digital Pressure Gauge

A digital pressure gauge is a measuring instrument used to determine and display the pressure of gases or liquids in a digital format. The pressure sensor converts the applied pressure into an electrical signal, which is then processed by the electronic circuitry. The processed signal is finally displayed as a numerical value on the digital screen. This pressure gauge is used in various industries such as manufacturing, automotive, oil and gas, aerospace and HVAC (heating, ventilation, and air conditioning). It is commonly used in quality control, process monitoring, equipment calibration, troubleshooting, and general pressure measurement tasks.

Battery Charger

Yelsons Battery charger is suitable for charging Lead Acid batteries, Lithium Polymer batteries, and LFP Batteries. It operates on an input voltage of 100VAC to 270V AC. The output voltage from the battery charger is 28.2VDC to 27.8VDC. It has surge immunity up to 7KV. The other feature is it draws zero current from the battery when the mains is OFF.

IN-PAD (TTL Output)

The device contains a voltage divider with TTL digital output. The voltage divider also contains its own positive High Voltage power supply for operating the radiation detector.

Smart Plug

Smart Plugs are power outlets that provide programmable and manual on/off control and real-time energy usage data of a connected device. A smart plug can replace a standard wall outlet, or sit in place between the wall outlet and the connected device. Wi-Fi or Bluetooth connectivity allows remote access from the bedroom to across the world via a smartphone or cloud application. The benefits provided Include the ability to:
Remotely turn ON and OFF any device.
Save money and conserve energy by eliminating standby power and scheduling on/off routines
Measure and record the power usage of a device – higher than normal power usage could indicate maintenance needs.

Home Automation

Transform your living space into a smart home with our innovative IoT devices. Control your lighting, appliances, security systems, and more from the convenience of your smartphone. Experience the comfort and efficiency of a connected home.

Energy Management System (Smart Energy Meter)

It is an Internet-capable device that allows you to monitor the usage of Energy, Natural gas, water, and power supply consumption or electric, voltage levels, and current. and power factor. The Smart Meter records your energy usage, and views the total consumption of devices in your home on its display. The user will be charged only for the energy used without having a stranger come into your home to take meter readings.

Vehicle Tracking System

The VTS is GPS-based vehicle location information in real-time, and shows that information on a map. The GPS Vehicle Tracking System assists organizations in simplifying the operation of their vessels in the most efficient and effective way, as well as an anti-theft tracking facility. Loconav’s car tracking system helps individuals and companies of all sizes to have tracking of vehicles on the road.

Remote Monitoring System

The Remote Monitoring System monitors and manages the facilities like power plants, factories, Genset, and industrial equipment remotely. With the help of RMS, one can access any equipment remotely anywhere. It is a revolutionary stepstone in the industry 4.0 development. It can be communicated over RS485, RS232, CAN, or any communication methodology available with the existing system.

URD-Underwater radiation detector

The system is used to measure sediment density during transport in rivers, lakes dams, etc. This device also measures the gamma radiations present in the water (in rivers, dams, lakes, etc.). The system has the arrangement to measure the equipment depth. All these parameters can be observed and analyzed on the software that is specially designed for the device.

Nuclear Electronic Products

Voltage Divider Network

Voltage Divider+ Pre-Amplifier

IN-PAD (TTL Output)

IN-PAD-IoT (LDS)

IN-PAD-LoRa

Single Channel Analyser

6- Channel Counter

12- Channel Counter